The Differences Between Acrylic and Polycarbonate


Category: clear acrylic, Polycarbonate
 

Acrylic and polycarbonate are two of the most popular plastics The Plastic People are asked questions about –  specifically what are the differences between acrylic and polycarbonate.  Here are some of the key areas to compare when choosing between acrylic and polycarbonate for your project.  We hope it helps – if you need more advice drop the friendly team at The Plastic People an email.

Strength – which is strongest

Polycarbonate is stronger than acrylic. That aside, both are very strong.

If you are comparing to glass, Acrylic and Polycarbonate are both half the weight of glass and yet both of these plastics are much stronger than glass.  Acrylic has 17 times the impact resistance of glass. Polycarbonate has 250 times the impact resistance of glass.

police riot shield – safe with polycarbonate

Acrylic is very rigid whereas polycarbonate can be bought in flexible grades. Acrylic cracks more easily than polycarbonate under stress.

Light – which has better clarity

Acrylic lets in more light with a light transmittance of 92% compared to  Polycarbonate which has a light transmittance of 88 percent.  That aside, both are used successfully for glazing – for example, polycarbonate is often used in bus shelter glazing as it is so strong and both acrylic and polycarbonate are used for secondary glazing.

secondary glazing – use either acrylic or polycarbonate

Acrylic can be polished to restore its clarity, while polycarbonate cannot.

Working with Acrylic & Polycarbonate

Acrylic can be used at temperatures ranging from -30 degrees Fahrenheit to 190 degrees Fahrenheit. It may expand and contract with changes in temperature although it won’t permanently shrink over time.

Polycarbonate can handle temperatures up to 240 degrees Fahrenheit. Polycarbonate is also highly resistant to chemicals such as gasoline and acids.

Which is easier to cut

Both acrylic and polycarbonate can be cut with conventional tools such as saws or routers, though acrylic cuts easier than polycarbonate. Polycarbonate fights the initial push of a saw or router at the start of a cut.

Which is easier to drill

Acrylic will crack if it is drilled near an edge or with a drill bit not designed for plastic. Polycarbonate typically does not crack when being drilled even if drilled close to the edge with a standard drill bit.

Which polishes up better

The edges of acrylic can be polished smooth and to a high shine. Polycarbonate cannot be polished.

polished acrylic table

Which is easier to bend 

Heat bending works better with acrylic than polycarbonate. Polycarbonate can be cold formed or bent without heating.

Which is easier to glue

Gluing with cements designed for acrylic and polycarbonate, acrylic gives a cleaner glue joint than polycarbonate.

Which is easier to keep clean

Both acrylic and polycarbonate are easy to clean. The best choice for cleaning is a micro fibre or 100% cotton cloths (no other types!).

Acrylic should only be cleaned with warm soap water or an acrylic cleaner.  Chemicals should never be used on acrylic.

Polycarbonate has a higher chemical resistance than acrylic; it can be cleaned by harsher cleaners containing chemicals such as ammonia.

Neither plastic should be cleaned with solvents.

Which is more durable

Both acrylic and polycarbonate are weather resistant and expand and contract with temperature changes without long-term or permanent shrinkage.

Both acrylic and polycarbonate can scratch, so avoid touching them with anything made from abrasive binding agents.

Acrylic is more likely to chip than polycarbonate because it is less impact-resistant. It does not scratch as easily, however, and will not yellow over time.

Polycarbonate has low flammability, while acrylic will burn slowly and is not recommended in areas where flames may be present.

Which is cheaper

Acrylic is cheaper to than Polycarbonate.

 

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>